Tag: Antique boat

Posted on

Adding the Shiny Parts

Stainless Steel cutwater
Adding the stainless steel cutwater and rub rails really add the finishing touches.

Chrome and highly polished stainless steel are beautiful things on a Chris Craft.  They really make the boat pop.  Don’t cheap-out on your re-chroming.  There aren’t a lot of chrome shops left in the U.S.  It’s a nasty, dirty process that takes a craftsman’s eye and touch to do right.  It’s expensive, but if you want it to last, you’ve got to pay for it.

Stainless is a little easier.  It’s not terribly expensive yet, and often it’s easier to replace than to try to refurbish.  But if it’s not deformed, a buffing wheel and a little elbow grease can go a long way to making some old stainless look better. Continue reading “Adding the Shiny Parts”

Posted on

Connecting the Exhaust Pipe

The exhaust pipe to exhaust elbow can be problematic because of heat and water.
The exhaust pipe to exhaust elbow can be problematic because of heat and water.

Connecting the exhaust pipe to the exhaust elbow can be problematic for a couple of reasons:  it gets hot and it gets wet.  Oh yeah, and it needs to be air tight so you don’t end up leaking exhaust into the boat. Continue reading “Connecting the Exhaust Pipe”

Posted on

Installing the Crashpad

Crashpad really dresses up the edge where the cockpit joins the deck.
Crashpad really dresses up the edge where the cockpit joins the deck.

The final step in the upholstery phase is to install the crashpad.  Crashpad is the 1/2 round closed cell foam rubber padding applied to the edge of the cockpit.  It is best left for after the varnish work and deck seams are complete.  So now’s the time. Continue reading “Installing the Crashpad”

Posted on

Caulking the Deck Seams

I use Sikaflex 291 LOT to caulk the deck seams.
I use Sikaflex 291 LOT to caulk the deck seams.

After the varnish is laid on, but before the final coat, it’s time to caulk the deck seams.  Most of them (2 out of 3) are false seams–only there for show.  But every third one is live.  It is essential to get a good seal with the seam caulking to prevent leaks and rot.   Continue reading “Caulking the Deck Seams”

Posted on

Varnishing the 1949 Chris Craft 17 ft Deluxe Runabout

Stern view after 3 coats of conventional varnish
Stern view after 3 coats of conventional varnish

Staining is just preparation for varnishing.  We talked about staining recently here.  Now it’s time for a bit of strategizing.  We’re anticipating about 6 coats of conventional varnish (Interlux Schooner 96) and then about 8-10 coats of AwlWood MA Gloss over that.  When you’re talking about that many coats, spraying is the way to go. Continue reading “Varnishing the 1949 Chris Craft 17 ft Deluxe Runabout”

Posted on

Installing the K Engine

Here's the engine ready to be lowered away to its new home.
Here’s the engine ready to be lowered away to its new home.

It was finally time to put the engine back in to this boat.  Check out the post on rebuilding it and running it.  Also, Chris Craft didn’t install oil filters on these engines.  Can you believe it?  Well we did, and here’s our discussion of it. Continue reading “Installing the K Engine”

Posted on

Installing a New Fuel Tank

New aluminum 20 gallon cylindrical tank
New aluminum 20 gallon cylindrical tank

The first question is: Can you use your old fuel tank, or do you need a new one?  That depends.  What material is your old fuel tank made of?  If it’s steel, or galvanized steel, I don’t think I’d entertain the notion of reusing one older than 5-10 years.  And I’d check it thoroughly for corrosion and pinholes even then.  It’s a pretty simple procedure to leak test a tank–fill it up and see if it leaks.  An even better test is a pressure test–something that all plumbers do for any new plumbing they install.  Simply plug it up and put a gauge on it.  Then pressurize it with 5-10 psi to see if it leaks down over time. Continue reading “Installing a New Fuel Tank”

Posted on

Fixing the Dash

The evil staple rot again! We've got to fix this before our new upholstery staples will hold in the edge of the dashboard.
The evil staple rot again! We’ve got to fix this before our new upholstery staples will hold in the edge of the dashboard.

We’ve referred to the evils of steel staples and the rot they produce in wood over time in a previous post here.  Well, that staple rot exists in the top of the dashboard too, since the crash pad was stapled to it as well.  We can either rebuild the dashboard, or restore it.  In this case, cutting out the offending strip, and gluing in a “Dutchman” will fit the bill. Continue reading “Fixing the Dash”

Posted on

How Do You Enlarge a Hole?

How to make a large hole larger? Don't run for your rasp or round file.
How to make a large hole larger? Don’t run for your rasp or round file.

The engine compartment ventilation holes needed enlarging.  For whatever reason, they were seriously undersized according to the plans, and my calculations of what is necessary for that size space.

So, if you already have a hole in the boat, how do you make it bigger?  How do you get your hole saw, or your drill bit to center itself on the hole, when there’s nothing there for the pilot bit to bite into? Continue reading “How Do You Enlarge a Hole?”

Posted on

New Ceiling Planks

New ceiling planks have to be fitted, then taken back out of the boat for staining and finishing.
New ceiling planks have to be fitted, then taken back out of the boat for staining and finishing.

Boat vocabulary can be crazy and frustrating.  For example, what do you call the planks that line the inside of the cockpit, and give it that beautiful, rich look?  Why the ceiling planks, of course.  And you thought that word meant an overhead surface, didn’t you?

New ceiling, port and starboard.
New ceiling, port and starboard.

Oh well, I didn’t really like the look of the old ceiling planks I took out.  And it was a simple matter to use the old ones as patterns and make new.  Actually it was easier to make new than to strip and refinish the old ones.  Not to mention the risk that one of the old, brittle planks might break when putting them back in.

How to hold the pieces in place while you fit them requires some creative solutions.
How to hold the pieces in place while you fit them requires some creative solutions.

 

 

The challenge was how to clamp the new planks in when fitting them.  That is often the case.  Boatbuilders as a group are some of the most creative clampers I know.